Forum Discussion

Anonymous's avatar
Anonymous
Not applicable
9 years ago
Solved

PowerQuery if with multiple conditions AND OR

Hello Guys,

How can I replicate this on PowerQuery ??

 

=if(ATC[WorkitemAssetState]=64,
if(ATC[WorkitemIsClosed]=FALSE,
if(ATC[WorkitemIsDeleted]=FALSE,
if(ATC[M_WorkitemStatus]IN{"","Reviewing","Available","Research","Progressing","Testing","Resolved","<none>"},
if(ATC[M_DefectResolutionId]IN {"-","<Unknown>","Resolution:1","Resolution:7"},1,-1)
,0)
,0)
,0)
,0)

I have done the following, but it does not seem to work properly:

if [WorkitemAssetState]=64 and
[WorkitemIsClosed]="FALSE" and
[WorkitemIsDeleted]="FALSE" and
[M_WorkitemStatus]="Reviewing" or [M_WorkitemStatus]= "Available" or [M_WorkitemStatus]= "Research" or [M_WorkitemStatus] = "Progressing" or [M_WorkitemStatus] = "Testing" or [M_WorkitemStatus] = "Resolved" or [M_WorkitemStatus] = "<none>" or [M_WorkitemStatus] = "<none>" or [M_WorkitemStatus] = "-" and
[M_DefectResolutionId]= "-" or [M_DefectResolutionId] = "<Unknown>" or [M_DefectResolutionId] = "Resolution:1" or[M_DefectResolutionId] = "Resolution:7" then 1 else 0

I am pretty sure its because of the multiple OR statements, dont think its because of "FALSE" btw.

Thanks!!


Need Help
  • v-ljerr-msft's avatar
    v-ljerr-msft
    9 years ago

    Hi Anonymous,

     

    Based on my test, the formula below should work in PowerQuery. :smileyhappy:

     

    =if [WorkitemAssetState]=64 and
[WorkitemIsClosed]=false and
[WorkitemIsDeleted]=false and
([M_WorkitemStatus]="Reviewing" or [M_WorkitemStatus]= "Available" or [M_WorkitemStatus]= "Research" or [M_WorkitemStatus] = "Progressing" or [M_WorkitemStatus] = "Testing" or [M_WorkitemStatus] = "Resolved" or [M_WorkitemStatus] = "<none>" or [M_WorkitemStatus] = "" or [M_WorkitemStatus] = "-" )and
([M_DefectResolutionId]= "-" or [M_DefectResolutionId] = "<Unknown>" or [M_DefectResolutionId] = "Resolution:1" or[M_DefectResolutionId] = "Resolution:7") then 1 else 0

     

    Regards

3 Replies

  • v-ljerr-msft's avatar
    v-ljerr-msft
    Microsoft Employee
    9 years ago

    Hi Anonymous,

     

    Based on my test, the formula below should work in PowerQuery. :smileyhappy:

     

    =if [WorkitemAssetState]=64 and
[WorkitemIsClosed]=false and
[WorkitemIsDeleted]=false and
([M_WorkitemStatus]="Reviewing" or [M_WorkitemStatus]= "Available" or [M_WorkitemStatus]= "Research" or [M_WorkitemStatus] = "Progressing" or [M_WorkitemStatus] = "Testing" or [M_WorkitemStatus] = "Resolved" or [M_WorkitemStatus] = "<none>" or [M_WorkitemStatus] = "" or [M_WorkitemStatus] = "-" )and
([M_DefectResolutionId]= "-" or [M_DefectResolutionId] = "<Unknown>" or [M_DefectResolutionId] = "Resolution:1" or[M_DefectResolutionId] = "Resolution:7") then 1 else 0

     

    Regards

    • Anonymous's avatar
      Anonymous
      Not applicable
      9 years ago

      Thank you, I managed in the end. Thank you! :)

      • Technowolf's avatar
        Technowolf
        Helper II
        7 years ago

        Hi

        How did you solve this, I still have the same issue,
        I syntax is excatly the same , the moment I add the or conditions the and conditions stops to work.