Problem in semantic model activities setting on Data Pipeline back to no selection when reopen again

[HelloTheSun]

Hello

I try to create new data pipeline and connect semantic models activities in the part of this pipeline

when setup completely after that all pipeline have been run successfully.

But when I reopen to check the setting in semantic models activities, my setup are back to no selection whether workspaces, models and tables, although pipeline is still running normally, if don't save to replace the existing version.

when setup completely and save.

after that open again, my setting back to no selection.

This problems are very annoy when I try to fix or adjust some config, I have to set all setting in semantic model activities again and again.

Anyone, Are there anyway fix this problems

Thank for your reply

[v-lgarikapat]

Hi @HelloTheSun ,

Thanks for sharing the details and screenshots  it definitely sounds frustrating to have to reconfigure the semantic model activity every time you reopen the pipeline, even though the pipeline itself runs fine.

To help understand the issue more clearly and provide better suggestions, could you please clarify a few things

1. Which region is your Fabric workspace hosted in, and are you using a trial or a fully licensed workspace?

2. What browser are you using when you're editing and saving the pipeline (e.g., Chrome, Edge, Firefox)?

3. Is this problem happening with all semantic models, or only one specific model you're working with?

4. Are other pipeline activities saving their configurations correctly, or is it only the Semantic model refresh activity that resets after saving and reopening?

5. How often are you reopening the pipeline and noticing that the activity settings are reset?
   For example, is it immediately after saving and closing, or only after several hours or days?

6. After the pipeline runs successfully the first time, does the second or scheduled run also complete successfully even if the settings appear blank when you reopen the activity?

Looking forward to your response this will help in narrowing down the root cause or suggesting a workaround.

Best regards,
Lakshmi Narayana

[HelloTheSun]

And now I have another problems in semantic model activity.

I try to set the partial refresh in some of tables in my model but when I click in "Tables" dropdown when load finished, it pop up the text "No results found" 

Please advise me if you have anyway to solve this problems or other ways how to apply the partial refresh with specific tables such as use the parameter with "Add dynamic content"

Thank you and best regards,

[v-lgarikapat]

Hi @HelloTheSun ,

Thank you for your detailed explanation and screenshots.

To help resolve the issue, I recommend raising a support ticket so the support team can assist you further.
Please refer to the following link for instructions on how to create a support ticket:

How to create a Fabric and Power BI Support ticket - Power BI | Microsoft Learn

We appreciate your engagement and thank you for being an active part of the community.

Best regards,
Lakshmi

[v-lgarikapat]

Hi @HelloTheSun ,

I wanted to follow up and check if you had a chance to raise the support ticket as we discussed earlier. Also, have you had an opportunity to review the information we shared?

If you have any questions or need further clarification, please feel free to reach out. I'm happy to assist.

Best regards,
Lakshmi

[HelloTheSun]

Thank you so much for your reply.

1. Which region is your Fabric workspace hosted in, and are you using a trial or a fully licensed workspace?
   Answer : Premium Capacity Workspace (P1 license)
   
   

2. What browser are you using when you're editing and saving the pipeline (e.g., Chrome, Edge, Firefox)?
   Answer : I try to test in Chrome and Edge and the problems happening in both browsers.
   
   

3. Is this problem happening with all semantic models, or only one specific model you're working with?
   Answer : Yes, problem happening with all semantic model activities in all data pipelines.
   
   

4. Are other pipeline activities saving their configurations correctly, or is it only the Semantic model refresh activity that resets after saving and reopening?
   Answer : Correct, In addition this problem happening in Team and Outlook activities too but all of problems activities have been run successfully.
   
   

5. How often are you reopening the pipeline and noticing that the activity settings are reset?
   For example, is it immediately after saving and closing, or only after several hours or days?
   Answer : All the time and when after saving and close the pipeline, after that reopen immediately all of my setup to be reset.
   
   

6. After the pipeline runs successfully the first time, does the second or scheduled run also complete successfully even if the settings appear blank when you reopen the activity?
   Answer : Second time and any schedule refresh will run successfully.