Forum Discussion
Paginated Report Builder - Chart does not fully generate within the designated Chart Area
Community SupportHi Anonymous ,
It looks like you are use print layout instead of preview, right?
On the left side there is a huge blank area. I looked for Paddings or Margins but there is nothing like it under the properties
You need to check whether you put chart close to left border of design pane?
On the right side the chart should go until a 100, because the chart is a 100% Column Chart. It stops about 80%.
According to your chart, I think a line will be 100%, you could view it in chart, all value in a line is 100%, so it will show 80% in last line(20% is Active)
On the top the legend is not aligned to the middle of the chart area
You need to make sure the chart area whether include Y-axis
On the bottom I added the X asis, however it is not visible. Without that some of the column charts wouldn't be visible.
I could view it in your chart, did you mean that this part can't view in your chart?
By the way, if possible, could you please upload your rdl file(create this report with virtual data instead of real data) and some sample file ? Then I will try to check and modify it in my environment.
Best Regards,
Zoe Zhi
If this post helps, then please consider Accept it as the solution to help the other members find it more quickly.
Hi Zoe,
Yes, I am using the print view. In the preview it shows correctly, but the issue is with the print view. It is causing a problem when I try to make a print of it.
I added some cleared manual data and I removed the confidential one. The other difference is that I didn’t add a manual colouring to the chart and legend so Passed tasks shows red instead of green. I shared the report at the end of this message.
Left side blank area:
I checked the sizes and everything is within the page size. The page is an A4 landscape (29.7x21cm with 1cm margins) and the body width is 27cm. I tried to resize the chart, but the issue is still the same on the print view. The preview is OK.
Missing area between 80% and 100%
Preview shows okay with no issue:
On the print preview the chart seems to have a left and top margin causing the X axis title and the end of the chart disappear. I am starting to think about an inherited value from somewhere, but from where...
On this one I changed the alignment of the legend to the right. As you can see it disappeared, however the end of the chart is pushed back a bit. (print view)
Top Legend not aligned
In print view it seems that the left and top margin pushes the legend to the right a bit.
Bottom X axis
Apologies, I meant X axis title. The X axis is visible.
Report File
Please find the link for it below:
https://drive.google.com/file/d/1dTv77hrpduppoLrKlqmfUZds7JXM40OT/view?usp=sharing
Thank you for your help.
Zsolt
- dax
Hi Anonymous ,
It seems that you send a correct sample to me, I open this in my environment, I find which works well. I don't modify it
Best Regards,
Zoe ZhiIf this post helps, then please consider Accept it as the solution to help the other members find it more quickly.
Hi Zoe,
On my end the Preview and Print view are still shows a different versions.
If I try to print the visuals still not showing on the correct place, however if I publish it to the BI Service it has the correct alignment.
It seems I need to trust in the Preview and work with the BI Services.
I raised a call with Microsoft to advise on my Desktop Report Builder, I will share their insight.
I uninstalled, reinstalled, repaired the desktop version, the issue is the same.
Zsolt
Solution:
After raising a ticket with Microsoft they were able to reproduce the problem.
The problem came from the inherited value of Scalie and Layout under the display settings.
I had the scaling value set for 150%. After changing it to 100% the Printing layout and Preview shows the same output, no issue with the Axis Titles or the Legend not showing.
Thank you all for your help.