Forum Discussion

tyagiyash32's avatar
tyagiyash32
Icon for Helper I rankHelper I
7 years ago
Solved

Drill down Suggestion

Hi, 

the data is as shown in image:

 

so in a barchart on axis as region and country (drill down) & on values it shoud reflect the calculated measure, i.e. M, L1. That drill down easily shows region name>country name> and their respective M & L1 values, but I need to drill down that to lower levels to reflect MS, MG, MLa, M Lo,... so on and same for L1 vakues. Sysdate is the date filter.

Need Help

13 Replies

  • v-cherch-msft's avatar
    v-cherch-msft
    Icon for Microsoft Employee rankMicrosoft Employee
    7 years ago

    Hi tyagiyash32 

    You may use 'unpivot column' in query editor for Units,M S...L1 C,L1 On columns.Then create measures as below.

    M =
CALCULATE (
    SUM ( Table1[Value] ),
    FILTER ( Table1, LEFT ( Table1[Attribute], 1 ) = "M" )
)
    / CALCULATE (
        COUNT ( Table1[Attribute] ),
        FILTER ( Table1, LEFT ( Table1[Attribute], 1 ) = "M" )
    )
    / CALCULATE (
        SUM ( Table1[Value] ),
        FILTER ( Table1, Table1[Attribute] = "Units" )
    )

    L =
CALCULATE (
    SUM ( Table1[Value] ),
    FILTER ( Table1, LEFT ( Table1[Attribute], 2 ) = "L1" )
)
    / CALCULATE (
        COUNT ( Table1[Attribute] ),
        FILTER ( Table1, LEFT ( Table1[Attribute], 2 ) = "L1" )
    )
    / CALCULATE (
        SUM ( Table1[Value] ),
        FILTER ( Table1, Table1[Attribute] = "Units" )
    )

    Regards,

    • tyagiyash32's avatar
      tyagiyash32
      Icon for Helper I rankHelper I
      7 years ago

      Hi Cherie,

       thanks for the quick response, i did the steps mentioned by you but still measures 'M' & 'L' doesn't drills down to the lower values. can you share me a an image where 'M' & 'L' gets drilled down M S...L1 C,L1...

      Regards

      Yash

      • tyagiyash32's avatar
        tyagiyash32
        Icon for Helper I rankHelper I
        7 years ago

        Sorry my bad i was not considering attibutes column in axis, the chart gets drilled down to M S...L1 C,L1... now but the respective values are coming as infinity, do you have any clue how the values can be corrected? I was looking to show values as percentages.

  • v-cherch-msft's avatar
    v-cherch-msft
    Icon for Microsoft Employee rankMicrosoft Employee
    7 years ago

    Hi tyagiyash32 

    Please check below measure and add an index column in query editor.

    M = 
IF (
    LEFT ( MAX ( Table1[Attribute] ), 1 ) = "M",
    CALCULATE (
        SUM ( Table1[Value] ),
        FILTER (
            ALL ( Table1 ),
            Table1[Index] <= MAX ( Table1[Index] )
                && LEFT ( Table1[Attribute], 1 ) = "M"
        )
    )
        / CALCULATE (
            COUNTROWS ( FILTER ( ALL ( Table1 ), LEFT ( Table1[Attribute], 1 ) = "M" ) )
        )
        / CALCULATE (
            SUM ( Table1[Value] ),
            FILTER ( ALL ( Table1 ), Table1[Attribute] = "Units" )
        )
)

    L = 
IF (
    LEFT ( MAX ( Table1[Attribute] ), 2 ) = "L1",
    CALCULATE (
        SUM ( Table1[Value] ),
        FILTER (
            ALL ( Table1 ),
            Table1[Index] <= MAX ( Table1[Index] )
                && LEFT ( Table1[Attribute], 2 ) = "L1"
        )
    )
)
    / CALCULATE (
        COUNTROWS ( FILTER ( ALL ( Table1 ), LEFT ( Table1[Attribute], 2 ) = "L1" ) )
    )
    / CALCULATE (
        SUM ( Table1[Value] ),
        FILTER ( ALL ( Table1 ), Table1[Attribute] = "Units" )
    )

    Regards,