Forum Discussion

nathan-verghis's avatar
nathan-verghis
Regular Visitor
1 year ago
Solved

Dataflow refresh job failed: Job instance failed without detail error

Hello,   I've been building a series of Dataflows to transform and load data between our Bronze and Silver Lakehouses across a couple different data providers. In my architecture, we have 1 dataflo...
Dataflow
Need Help
  • v-veshwara-msft's avatar
    v-veshwara-msft
    1 year ago

    Hi nathan-verghis ,
    Thanks for the follow-up.

    Since the issue persists even after trying the available workarounds and there's no clear indicator from the Dataflow logs, the best next step would be to raise a support ticket with Microsoft for deeper investigation. If you've already raised a support request, please consider sharing any insights or resolutions provided by the support team here, it would be helpful for others facing the same issue.

    Also thanks to miguel and Ilgar_Zarbali for addressing this and sharing your valuable insights.

     

    Best Regards,
    Vinay,
    Community Support Team.

     

v-veshwara-msft's avatar
v-veshwara-msft
Community Support
1 year ago

Hi nathan-verghis ,

Following up to see if your query has been resolved. If any of the responses helped, please consider marking the relevant reply as the 'Accepted Solution' to assist others with similar questions.

If you're still facing issues, feel free to reach out.

Thank you.

nathan-verghis's avatar
nathan-verghis
Regular Visitor
1 year ago

Unfortunately this is still an issue. I've attempted the solutions posted so far, however haven't had any success. So far just manually running the dataflow seems to work better than it being triggered by the pipeline on a schedule, but I don't see why that should cause any issues. For insight, this error tends to occur about a minute into the dataflow run, but I don't see any schema changes that would cause the issue (especially since this is only happening between Bronze and Silver, not the initial load into Bronze)

  • v-veshwara-msft's avatar
    v-veshwara-msft
    Community Support
    1 year ago

    Hi nathan-verghis ,
    Thanks for the follow-up.

    Since the issue persists even after trying the available workarounds and there's no clear indicator from the Dataflow logs, the best next step would be to raise a support ticket with Microsoft for deeper investigation. If you've already raised a support request, please consider sharing any insights or resolutions provided by the support team here, it would be helpful for others facing the same issue.

    Also thanks to miguel and Ilgar_Zarbali for addressing this and sharing your valuable insights.

     

    Best Regards,
    Vinay,
    Community Support Team.

     

    • v-veshwara-msft's avatar
      v-veshwara-msft
      Community Support
      1 year ago

      Hi nathan-verghis ,

      We’re following up as we haven’t heard from you in a while. May I ask if you were able to raise a support ticket and receive any guidance from the support team?

      If you’ve already shared the ticket details via direct message with miguel, that’s perfectly fine.

      If there are any key insights or resolutions you can share here (while keeping any sensitive information private), it would be helpful for others facing similar issues.

      If there are no further updates, we may consider closing this thread.

       

      For any future questions or assistance, please don’t hesitate to start a new discussion in the Microsoft Fabric Community Forum. We’ll be happy to help.

      Thank you for being a valued member of the Microsoft Fabric Community.

    • Guerrero's avatar
      Guerrero
      Frequent Visitor
      11 months ago

      Is this problem fixed? 

      • v-veshwara-msft's avatar
        v-veshwara-msft
        Community Support
        11 months ago

        Hi Guerrero ,

        Thanks for reaching out here.
        If you are facing this issue as well, it would be best to open a new thread with your specific details or raise a support ticket with Microsoft. Since the details discussed here are specific to another case, having a dedicated thread will help with a more accurate investigation.

         

        Regards,
        Vinay kumar.

  • miguel's avatar
    miguel
    Community Admin
    1 year ago

    Hi!

    My name is Miguel Escobar and I'm a product manager for Dataflow Gen2. Will be happy to help you reach a solution.

     

    Could you please share some more information?

    • Are you using a Dataflow Gen2 or is it a Dataflow Gen2 with CI/CD support?
    • Could you please share exactly where you're seeing the 20302 error? is it within the Data pipelines? if it is within the pipelines, could you please head over to the Workspace list, select the acitons menu of the Dataflwo that failed the refresh, select the option with the label "recent runs", find the run that failed and see what errors are shown within that detailed report of the failed refresh? if you could provide a screenshot of the error from the recent runs that would help tremendously

    If you have a support ticket, you can also share it with me via a private direct message and we can follow up through that secure support channel.